Here at Low Rate Automotive Locksmith we are your source for free instructions on how to program your GMC keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Locksmith offers detailed step-by-step directions from the manufacturer of your GMC car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.
Here is the list of GMC Safari Years and models this supports:
- 1995 GMC Safari
- 1996 GMC Safari
- 1997 GMC Safari
- 1998 GMC Safari
- 1999 GMC Safari
- 2000 GMC Safari
- 2001 GMC Safari
- 2002 GMC Safari
- 2003 GMC Safari
- 2004 GMC Safari
- 2005 GMC Safari
1995 GMC Safari Car Key Fob and Remote Programming Instructions:
1. Locate the Data Link Connector (DLC) underneath the driver’s side dashboard.
Use the figure as a map for your DL ( They are not lettered on your vehicle.)
The view is looking straight into the cavities of the DLC.
2. Connect cavity G with a ground using a fused jumper wire.
Your vehicle will respond by locking and unlocking the door locks within 2 seconds.
3. Press any button on first remote to be programmed.
Locks will lock and unlock verifying remote was programmed.
4. Press any button on second remote to be programmed if applicable.
Locks will lock and unlock to verify remote was programmed.
5. Remove jumper wire and test remote(s)
1996-1999 GMC Safari Car Key Fob and Remote Programming Instructions:
1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know which pins are 8 and 4.
(Notice port is wider on top row)
2. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable
jumper wire (leave the jumper wire connected throughout the programming procedure). Make
sure you know which terminals are 8 and 4. The vehicle will respond by locking and unlocking the
doors to signify entering of programming mode.
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be
programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors.
Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the OBDIIPort.
2000-2003 GMC Safari Car Key Fob and Remote Programming Instructions:
1. Close all vehicle doors.
2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing
12. Turn the ignition switch to the ON position in order to exit the transmitter programming
2004-2005 GMC Safari Car Key Fob and Remote Programming Instructions:
There is no onboard programming procedure for GMC Safari 2004-2005. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please contact your dealer or your local automotive locksmith.
If you have any questions or need a professional Locksmith To assist you with your GMC Safari Key Fab Programming, below is a list of Low Rate Locksmith Locations.
GMC Safari key fob programming service San Diego ca GMC Safari key fob programming service fair oaks ca
GMC Safari key fob programming service Stockton ca GMC Safari key fob programming service Roseville ca
GMC Safari key fob programming service Elk Grove ca GMC Safari key fob programming service Rocklin ca
GMC Safari key fob programming service Sacramento ca GMC Safari key fob programming service Lincoln ca
GMC Safari key fob programming service Carmichael ca GMC Safari key fob programming service Folsom ca
GMC Safari key fob programming service Citrus Heights ca GMC Safari key fob programming service San Francisco ca
[uuuuuuu”10″ grid_id=”vc_gid:1526154278662-6530a6c9-92bc-4″ taxonomies=”4224″]
The Chevrolet Astro was a rear-wheel drive mid-sized van introduced by Chevrolet in 1985 to rival domestic (American) competitors the Dodge Caravan/Plymouth Voyager twins and the Japanese Toyota Van. Also sharing the Astro’s platform was its sibling, the GMC Safari. In addition to standard passenger uses, the vans were also available as cargo vans, and converters used them as the basis for small conversion vans. Due to the truck-based powertrain, the Astro and Safari could pull 5,500 lb (2,500 kg) with proper equipment. The last Astro and Safari rolled off the assembly line on May 13, 2005.
In addition to their popularity as conversion vans the Astro and Safari both have popular followings with “back yard” modifiers.