Low Rate Locksmith

Toyota Avalon Key Replacement

Toyota Avalon Key Locksmith

If you are looking for a locksmith Toyota Avalon because you either lost your key or if you are looking to make a duplicate Toyota car key, then you have found the place that can help you! Our automotive department can make you a key if you have lost your Toyota Avalon car keys regardless of the year! Our mobile locksmith service for Toyota Avalon is available 24 hour a day 7 days a week!

Toyota Avalon Locksmith services provides a solution to the duplication of Toyota Avalon chip keys. Toyota Avalon chip key cut is a service that is offered to reduce the cost of replacing the key from the dealership which is expensive as it is almost thrice the cost of duplication of the key. For duplication, one is required to buy a blank transponder chip key from a Toyota Avalon Locksmith. The locksmith will then use your master transponder key to duplicate on the black transponder key. After the blank transponder key has been cut to duplicate the master transponder key, it will have to be programmed to work on your car. The Toyota Avalon locksmith provides the service of programming the key to work on your vehicle. Visit your nearest Toyota Avalon Locksmith to get the best Toyota Avalon Chip Key Cut services.

If you have looked around for the Toyota Avalon car keys, then you would have found that there are two types of these keys:

Metal and transponder Toyota Avalon car keys. Here is a description for both them and hopefully that will clear up the confusion.

Metal Toyota Avalon Keys:

Toyota Avalon’s that were made in 1995, 1996 and 1996 had metal key that does not use the car computer to operate the car. It’s just the good old plain metal key. To make a copy of that key, all you have to do is to go a any Home Depot or Wall Mart and ask them for a duplicate. usually it won’t cost more than $5. If you have lost all of your car keys, then you would have to call the closest Toyota dealership in your area and ask them for the KEY CODE for your car. They will ask you to provide the Vin Number of your car and a proof of ownership. Once the code is provided, go to a locksmith shop near you and ask them to CUT KEY BY CODE. and that’s it.

Toyota Avalon Transponder keys why it’s expensive:

The first thing that comes to a driver mind when losing a car key, is to go to the local dealership to buy a replacement key for your car. However, twenty years ago, Toyota Avalon started the use of electronic, transponder, chips keys that need to be programmed to the engine control module in order to start the vehicle, the car need to be towed to the dealership to be reprogrammed which made the whole procedure of a Toyota Avalon key made probably a pretty hard and in some cases might reach hundreds of dollars.

Lost Toyota Avalon Car Key?

Losing car keys is always a horrible experience for any car owner as it means any car services stall for the time the key is lost. Previously, one could easily just duplicate the key but with the ongoing technology advancement, dealers like Toyota Avalon introduced keys with chips to prevent theft of vehicles.

Toyota Avalon Remote Programming

1995 Toyota Avalon

1.  Start with Key out of ignition.

2.  Locate bulb failure warning module in trunk near LH hinge and disconnect multi-plug.

3.  Jump bulb failure warning module harness multi-plug terminals 2 and 10:  System should now lock and unlock vehicle once and activate truck lock to confirm.

4.  Press any button on keyless remote: System should now lock and unlock vehicle once and activate trunk lock to confirm.

5.  Press any button on second keyless remote if applicable: System should now lock and unlock vehicle once and activate trunk lock to confirm.

6.  To exit programming mode remove jumper wire from multi-plug. Reconnect multi-plug to original connection.

7.  Test remote(s).

** A maximum of 2 keyless remotes can be programmed.

** Programming a keyless remote erases all other keyless remotes. Both keyless remotes must be programmed at the same time.

2002 Toyota Avalon

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2003 Toyota Avalon

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2007 Toyota Avalon

This procedure is for 2007 Avalon models that have a separate key and remote. If you have a Smart Key you will have to have a Locksmith or Dealership program it for you.

Call Toll Free 855-899-6729 to find a locksmith in your area to program this remote.

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1996 Toyota Avalon

1.  Start with Key out of ignition.

2.  Locate bulb failure warning module in trunk near LH hinge and disconnect multi-plug.

3.  Jump bulb failure warning module harness multi-plug terminals 2 and 10:  System should now lock and unlock vehicle once and activate truck lock to confirm.

4.  Press any button on keyless remote: System should now lock and unlock vehicle once and activate trunk lock to confirm.

5.  Press any button on second keyless remote if applicable: System should now lock and unlock vehicle once and activate trunk lock to confirm.

6.  To exit programming mode remove jumper wire from multi-plug. Reconnect multi-plug to original connection.

7.  Test remote(s).

** A maximum of 2 keyless remotes can be programmed.

** Programming a keyless remote erases all other keyless remotes. Both keyless remotes must be programmed at the same time.

2000 Toyota Avalon

1. Start with key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.

3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
 A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks should cycle once indicating successful programming. If the door locks don’t cycle or cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

2004 Toyota Avalon

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2008 Toyota Avalon

This procedure is for 2008 Avalon models that have a separate key and remote. If you have a Smart Key you will have to have a Locksmith or Dealership program it for you.

Call Toll Free 855-899-6729 to find a locksmith in your area to program this remote.

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1997 Toyota Avalon

1.  Start with Key out of ignition.

2.  Locate bulb failure warning module in trunk near LH hinge and disconnect multi-plug.

3.  Jump bulb failure warning module harness multi-plug terminals 2 and 10:  System should now lock and unlock vehicle once and activate truck lock to confirm.

4.  Press any button on keyless remote: System should now lock and unlock vehicle once and activate trunk lock to confirm.

5.  Press any button on second keyless remote if applicable: System should now lock and unlock vehicle once and activate trunk lock to confirm.

6.  To exit programming mode remove jumper wire from multi-plug. Reconnect multi-plug to original connection.

7.  Test remote(s).

** A maximum of 2 keyless remotes can be programmed.

** Programming a keyless remote erases all other keyless remotes. Both keyless remotes must be programmed at the same time.

2001 Toyota Avalon

1. Start with key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.

3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
 A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks should cycle once indicating successful programming. If the door locks don’t cycle or cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

2005 Toyota Avalon

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1998 Toyota Avalon

1. Start with key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.

3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
 A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks should cycle once indicating successful programming. If the door locks don’t cycle or cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

1999 Toyota Avalon

1. Start with key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.

3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
 A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks should cycle once indicating successful programming. If the door locks don’t cycle or cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

2006 Toyota Avalon

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Our Toyota Avalon Key Replacement Service Area

Toyota Key Replacement Sacramento

Toyota Key Replacement Roseville ca

Toyota Key Replacement San Diego ca

Toyota Key Replacement Stockton ca