Automotive Locksmith we are your source for free instructions on how to program your Buick keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Locksmith offers detailed step-by-step directions from the manufacturer of your Buick car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.
Here is the list of Buick Riviera Years and models this supports:
- 1995 Buick Riviera
- 1996 Buick Riviera
- 1997 Buick Riviera
- 1998 Buick Riviera
- 1999 Buick Riviera
1995 Buick Riviera Car Key Fob and Remote Programming Instructions:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please contact your dealer or local automotive locksmith.
1996-1999 Buick Riviera Car Key Fob and Remote Programming Instructions:
- Insert key in ignition and leave in the OFF position
- Locate the Data Link Port. It is located under dash drivers side. Be sure you know
which pins are 8 and 4.
(Note port is wider at top) Your OBDII port will not
have numbers, use the for reference. - Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a
suitable jumper wire (leave the jumper wire connected throughout the programming
procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
by locking and unlocking the doors to signify entering of programming mode. - Close doors.
- Turn ignition to the ON position (as far as you can go without cranking the engine).
Doors will lock. - Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
be programmed. After about 15 seconds, the vehicle will respond by locking and
unlocking the doors. Release the buttons on the transmitter. - Within one minute, repeat the previous step on the remaining transmitters to be
programmed. - Remove jumper wire applied to the OBDII Port.
If you have any questions or need a professional Locksmith To assist you with your Buick Riviera Key Fab Programming, below is a list of Low Rate Locksmith Locations.
For more about Buick Riviera car key replacement Click Here
MORE MORE KEY FOB INSTRUCTIONS CLICK HERE
Buick Riviera key fob programming service San Diego ca Buick Riviera key fob programming service fair oaks ca
Buick Riviera key fob programming service Stockton ca Buick Riviera key fob programming service Roseville ca
Buick Riviera key fob programming service Elk Grove ca Buick Riviera key fob programming service Rocklin ca
Buick Riviera key fob programming service Sacramento ca Buick Riviera key fob programming service Lincoln ca
Buick Riviera key fob programming service Carmichael ca Buick Riviera key fob programming service Folsom ca
Buick Riviera key fob programming service Citrus Heights ca Buick Riviera key fob programming service San Francisco ca
The Riviera by Buick is an automobile produced by Buick in the United States from the 1963 to 1999 model years, with 1,127,261 produced.
A full-size hardtop, a specially trimmed and stretched sedan, or a personal luxury car, the early models of the Riviera in particular have been highly praised by automotive journalists and writers.
A common misconception is that all Rivieras produced after the 1965 model are front wheel drive cars; this is true only of the 1979–1999 models. In contrast, the Riviera’s E-body stablemates, the Oldsmobile Toronado and Cadillac Eldorado (subsequent to its change in platform in 1967), were always front-wheel drive.