Here at Low Rate Automotive Locksmith we are your source for free instructions on how to program your Dodge keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Locksmith offers detailed step-by-step directions from the manufacturer of your Dodge car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.
Here is the list of Dodge Ram Years and models this supports:
- 1996 Dodge Ram
- 1997 Dodge Ram
- 1998 Dodge Ram
- 1999 Dodge Ram
- 2000 Dodge Ram
- 2001 Dodge Ram
- 2002 Dodge Ram
- 2003 Dodge Ram
- 2005 Dodge Ram
1996 Dodge Ram Car Key Fob and Remote Programming Instructions:
1. Locate the keyless entry program line – a dark green wire with a molded
plastic insulator on the end. The program line is located under the left side
of the instrument panel. The wire is taped back to the harness (Left of the
steering column near the floor) and terminated with a black rubber mold.
2. Connect the program line from the Remote Keyless Entry Module to
ground with a suitable jumper wire.
3. Insert the key into the ignition and turn ignition switch to the ON position.
4. Press any button on the transmitter to set code. If there is a second
transmitter it has to be set at this time by pressing any button on the
second transmitter. The locks will lock and unlock automatically to
confirm programming.
5. Disconnect the program line from ground, turn ignition off and remove key.
1999-2001 Dodge Ram Car Key Fob and Remote Programming Instructions:
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.
1. Turn ignition to run position (as far as you can go without starting engine).
2. Using any Working remote, press the UNLOCK button for 4 to 10 seconds.
3. Within the specified 4 to 10 seconds, continue pressing the UNLOCK buton and press
the PANIC button for 1 second and release both buttons at the same time. A chime will
sound within 3 seconds to indicate that the vehicle has entered remote programming
mode.
4. Within 30 seconds of the chime, press any button on all remotes to be programmed
including previously programmed remotes. A chime will sound after each remote is
programmed.
5. Turn ignition to OFF and remove key.
6. Test all remotes.
2002-2005 Dodge Ram Car Key Fob and Remote Programming Instructions:
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.
1. Enter your vehicle and close all doors.
2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may
confuse you during this programming procedure.)
3. Place key into the ignition.
4. Turn the ignition to the ON position ( DO NOT START THE ENGINE )
5. Press and hold the UNLOCK button on a working remote.
6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.
7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.
8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.
9. A single chime will be heard. The chime indicates the the remote was recognized.
10. Within 4 seconds of hearing the chime, press and release any button on the remote
being programmed.
11. A single chime will be heard The chime indicates the remote has been programmed.
12. Repeat steps 8 to 11 for a total of 4 remotes.
13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.
If you have any questions or need a professional Locksmith To assist you with your Dodge Ram Key Fab Programming, below is a list of Low Rate Locksmith Locations.
For more about Dodge Ram car key replacement Click Here
MORE MORE KEY FOB INSTRUCTIONS CLICK HERE
Dodge Ram key fob programming service San Diego ca Dodge Ram key fob programming service fair oaks ca
Dodge Ram key fob programming service Stockton ca Dodge Ram key fob programming service Roseville ca
Dodge Ram key fob programming service Elk Grove ca Dodge Ram key fob programming service Rocklin ca
Dodge Ram key fob programming service Sacramento ca Dodge Ram key fob programming service Lincoln ca
Dodge Ram key fob programming service Carmichael ca Dodge Ram key fob programming service Folsom ca
Dodge Ram key fob programming service Citrus Heights ca Dodge Ram key fob programming service San Francisco ca
[uuuuuuu”10″ grid_id=”vc_gid:1526162081227-ac158cb7-a4cc-2″ taxonomies=”4224″]
The Ram (formerly the Dodge Ram) is a full-size pickup truck manufactured by Chrysler Group LLC. As of 2010, it has been sold under the Ram Trucks brand. Previously, Ram was part of the Dodge lineup of light trucks. The name Ram was first used in 1981 on the redesigned Ram and Power Ram following the retiring and rebadging of the Dodge D Series pickup trucks as well as B-series vans. The truck is named for the Ram hood ornament that first appeared on Dodge vehicles in 1933. The Ram Truck is in its fourth generation as of the 2009 model year.
Ram trucks have been named Motor Trend magazine’s Truck of the Year five times; the second-generation Ram won the award in 1994, the third-generation Ram Heavy Duty won the award in 2003, the fourth-generation Ram Heavy Duty won in 2010 and the current Ram 1500 won in 2013 and 2014.