GMC Acadia Key Fob Programming by Year

Can you program a Acadia fob without the dealer? For most years, yes. Pick your year for the route and best next step.

Find your year

YearDIY onboard?How it programsWorking fob?Erase riskConfidenceBest next step
2007–2010YesYes - onboard relearnNo (all-keys-lost OK)YesHighFollow the steps below
2017YesYes - onboard relearnVariesYesHighFollow the steps below
2018–2023YesYes - onboard relearnNo (all-keys-lost OK)YesMedFollow the steps below

GMC Acadia key types & programming facts

For 2007-2016 GMC Acadia models, remote programming can be done onboard through the vehicle information display or trip odometer reset controls, and the source notes that 2011 and newer vehicles may require a locksmith or dealership for programming. For 2021-2023 GMC Acadia models, the available fob is a 5-button smart key with lock, unlock, rear hatch, remote start, and panic functions, but the provided sources do not describe an onboard key-programming procedure for those years.

Key types used on the Acadia:

  • transponder chip key (2007-2016)
  • remote-head key (2007-2016)
  • smart/proximity push-to-start key (2021-2023)

Common fob FCC IDs: HYQ1ES — check the back of your fob; we confirm the exact variant on site.

2007–2010 GMC Acadia

Exact steps source-verified for this year/equipment

Route verified as onboard programming (no dealer needed). Steps below are source-verified for this year/equipment path.

Show the programming methods (18 steps)

2) Preparation

Insert the key
1 Insert key and turn to ON position to access Driver Information Center
Programming step
2 Locate vehicle information button on instrument cluster
Programming step
3 Locate set/reset button on instrument cluster
Doors lock-cycle (confirm)
4 Confirm availability of up to eight remotes for programming
Wait / timing window
5 Note memory recall seats: first remote = Driver 1, second remote = Driver 2

3) Entering Programming Mode

Press / hold a fob button
1 Press vehicle information button until "PRESS TO RELEARN REMOTE KEY" displays
Press / hold a fob button
2 Press set/reset button until "EMOTE KEY LEARNING ACTIVE" displays
Programming step
3 Programming mode ready for remote learning
Programming step
4 Repeat set/reset step to program additional remotes during same session
Programming step
5 Exit programming by turning key off and removing key

4) Remote Learning Procedure

Press LOCK + UNLOCK
1 Press and hold lock and unlock buttons on first keyless remote simultaneously
Press / hold a fob button
2 Hold buttons for approximately 15 seconds
Doors lock-cycle (confirm)
3 Chime sounds indicating remote programmed
Programming step
4 Repeat procedure for additional remotes as needed
Programming step
5 Test remote(s) after programming

5) Troubleshooting & Accessories

Programming step
1 Question: "Can I Program an ignition key for this vehicle?" (listed, no answer provided)
Programming step
2 Key fob battery note: "Key Fob Not Working? Have You Tried Replacing the Battery?"
Programming step
3 Home | Disclaimer | YouTube | Privacy Policy navigation links listed

2017 GMC Acadia

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (15 steps)

Programming with two recognized transmitters

Programming step
1 Both recognized transmitters must be present and vehicle must be off
Programming step
2 Place two recognized transmitters in cup holder before starting
Remove the key
3 Remove driver door key lock cylinder cap and insert vehicle key of new transmitter
Turn ignition to ON
4 Turn key counterclockwise to unlock position five times within 10 seconds; DIC displays READY FOR REMOTE #2, 3, 4, ETC.
Press LOCK + UNLOCK
5 Place new transmitter in center console transmitter pocket, press ENGINE START/STOP, then remove and press UNLOCK or LOCK; repeat for additional transmitters and hold ENGINE START/STOP for 12 seconds to exit

Programming without recognized transmitters

Programming step
1 Procedure available when two recognized transmitters are not available; feature not available in Canada
Programming step
2 Vehicle must be off and all transmitters to be programmed must be present; process takes ~30 minutes
Remove the key
3 Remove driver door key lock cylinder cap, insert vehicle key and turn counterclockwise five times within 10 seconds; DIC displays REMOTE LEARN PENDING, PLEASE WAIT
Hold fob to START button
4 Wait 10 minutes until DIC displays PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP; repeat this press-and-wait step two additional times to erase previous transmitters
Press LOCK + UNLOCK
5 After READY FOR REMOTE #1 appears, place new transmitter in transmitter pocket, press ENGINE START/STOP to learn, remove and press UNLOCK or LOCK; repeat for additional transmitters and hold ENGINE START/STOP for 12 seconds to exit

Transmitter pocket and physical key handling

Programming step
1 Transmitter pocket located inside center console storage area between driver and front passenger seats
Programming step
2 Key lock cylinder cap located on driver door handle; cap must be removed to access cylinder
Programming step
3 Vehicle key from new transmitter must be inserted into door lock cylinder for programming steps
Programming step
4 After programming, return key to transmitter by placing key back into the transmitter
Cycle the ignition ON/OFF
5 Removal and reinsertion actions required during programming cycles (cup holder placement, pocket placement, pressing buttons)

2018–2023 GMC Acadia

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (20 steps)

Programming with recognized transmitters (prerequisites & setup)

Programming step
1 Vehicle must be off and all transmitters (recognized and new) must be present
Programming step
2 Two recognized transmitters required to use this method
Programming step
3 Place the two recognized transmitters in the cup holder
Remove the key
4 Remove key lock cylinder cap on driver door handle before inserting key
Programming step
5 New transmitter’s vehicle key required for turning in driver door lock cylinder

Programming with recognized transmitters (step sequence)

Insert the key
1 Insert vehicle key of new transmitter into driver door cylinder and turn counterclockwise to unlock position five times within 10 seconds
Programming step
2 DIC displays READY FOR REMOTE #2, 3, 4, ETC after successful key turns
Programming step
3 Place new transmitter into the transmitter pocket inside center console storage area
Press / hold a fob button
4 Press ENGINE START/STOP to learn transmitter; DIC prompts ready for next transmitter
Press LOCK + UNLOCK
5 Remove transmitter and press UNLOCK or LOCK; repeat Steps 3–5 for additional transmitters; press and hold ENGINE START/STOP for 12 seconds to exit programming mode

Programming without recognized transmitters (prerequisites & initial steps)

Programming step
1 Vehicle must be off and all transmitters to be programmed must be present
Remove the key
2 Remove key lock cylinder cap on driver door handle and insert vehicle key of a transmitter
Turn ignition to ON
3 Turn key counterclockwise to unlock position five times within 10 seconds to initiate REMOTE LEARN PENDING
Hold fob to START button
4 Wait for DIC to display PRESS ENGINE START BUTTON TO LEARN (about 10 minutes)
Press / hold a fob button
5 Press ENGINE START/STOP when prompted; DIC will again show REMOTE LEARN PENDING, PLEASE WAIT

Programming without recognized transmitters (completion steps)

Programming step
1 Repeat pressing ENGINE START/STOP two additional times; after third time all previous transmitters will no longer work
Programming step
2 DIC should display READY FOR REMOTE #1 after third ENGINE START/STOP sequence
Press / hold a fob button
3 Place new transmitter in transmitter pocket (center console storage area) and press ENGINE START/STOP to learn each transmitter
Press LOCK + UNLOCK
4 Remove transmitter and press UNLOCK or LOCK to confirm; repeat for up to eight transmitters; press and hold ENGINE START/STOP for 12 seconds to exit programming mode
Programming step
5 Replace key back into the transmitter after programming complete

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

YearRoute statusExact steps
2007–2010Route verifiedSource-verified
2017Route verifiedGeneral guidance
2018–2023Route verifiedGeneral guidance

Common questions

Can the GMC Acadia remote be programmed onboard?

Yes for 2007-2016 models, using an onboard relearn procedure described by the source.

What functions does the 2021-2023 GMC Acadia smart key support?

The listed 5-button smart key supports lock, unlock, rear hatch, remote start, and panic.

Do all GMC Acadia years use the same key type?

No. The sources show 2007-2016 remote/key fob programming, while 2021-2023 use a smart/proximity-style key fob.

Can you program a Acadia key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your Acadia fob programmed? We come to you, 24/7.
Scroll to Top
☎  Tap to call 24/7 — (833) 439-8636