Cadillac CT5 Key Fob Programming by Year

Can you program a CT5 fob without the dealer? For most years, yes. Pick your year for the route and best next step.

Find your year

YearDIY onboard?How it programsWorking fob?Erase riskConfidenceBest next step
2020YesYes - onboard relearnYes (2 working)PossibleHighFollow the steps below
2021YesYes - onboard relearnYes (2 working)HighFollow the steps below
2022YesYes - onboard relearnHighFollow the steps below

Cadillac CT5 key types & programming facts

2020–2022 Cadillac CT5 models in North America use a smart proximity key fob with an emergency mechanical insert key for door access if the battery is dead. Programming replacement fobs is typically done via onboard procedures or with professional diagnostic equipment so the vehicle’s immobilizer and keyless entry systems recognize the new fob. Once programmed, the fob supports passive entry, push-button start, trunk release, panic, and other remote functions depending on button configuration.

Key types used on the CT5:

  • smart/proximity push-to-start key (keyless entry remote with emergency insert key) (2020-2022)

Common fob FCC IDs: YG0G20TB1 — check the back of your fob; we confirm the exact variant on site.

2020 Cadillac CT5

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (24 steps)

Vehicle capacity and general notes

Programming step
1 Up to eight remote keys can be matched to each vehicle.
Programming step
2 New key programming requires vehicle to be in RUN.
Programming step
3 Programming can proceed when two recognized keys are available.
Wait / timing window
4 Programming mode exited by holding ENGINE START/STOP ~12 seconds.
Programming step
5 Locksmith required if two recognized keys are not available.

Programming with recognized remote keys — preparation

Programming step
1 Place two recognized remote keys on the passenger seat.
Programming step
2 Access the DIC (Driver Information Center) and scroll to Remote Key Relearn.
Programming step
3 DIC will display READY FOR REMOTE #3, 4, 5, etc.
Programming step
4 Keep both recognized and new remote keys physically present during procedure.
Programming step
5 New remote key placed into the rear cupholder for learning.

Programming with recognized remote keys — steps

Programming step
1 With vehicle in RUN, place new remote key in rear cupholder.
Press / hold a fob button
2 Press ENGINE START/STOP to initiate learning of the new remote.
Doors lock-cycle (confirm)
3 DIC confirms when the remote key is learned and ready for next key.
Doors lock-cycle (confirm)
4 Remove newly learned remote from rear cupholder after confirmation.
Press LOCK + UNLOCK
5 Press UNLOCK or LOCK on the newly learned remote to complete learning step.

Programming additional remotes and exit

Programming step
1 Repeat the learn steps to program additional remote keys as needed.
Cycle the ignition ON/OFF
2 DIC cycles READY FOR REMOTE numbers for each additional key.
Wait / timing window
3 After all additional remotes are programmed, hold ENGINE START/STOP for ~12 seconds to exit.
Programming step
4 Total number of remotes can reach up to eight when all are programmed.
Press LOCK + UNLOCK
5 Confirm each remote by pressing UNLOCK or LOCK after learning.

Programming without recognized remote keys — locksmith guidance

Programming step
1 Locate an automotive locksmith using the provided phone number or website.
Programming step
2 Driving the vehicle to the locksmith may reduce cost versus mobile service.
Programming step
3 Locksmith will use specialized computer equipment to program the smart key remote fob.
Programming step
4 Procedure required when two currently recognized remote keys are not available.

2021 Cadillac CT5

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (19 steps)

Vehicle capacity and general notes

Programming step
1 Up to eight remote keys can be matched to each vehicle.
Programming step
2 New keys require presence of two recognized keys for self-programming.
Programming step
3 Programming can proceed with vehicle in RUN mode.
Programming step
4 Programmed remote keys display status on the DIC (Driver Information Center).
Wait / timing window
5 Exit programming mode by pressing and holding ENGINE START/STOP for ~12 seconds after programming all remotes.

Programming with recognized remote keys — required items

Programming step
1 Two recognized remote keys placed on the passenger seat.
Programming step
2 New remote key placed in the rear cupholder.
Programming step
3 Vehicle set to RUN while performing programming steps.
Programming step
4 DIC menu selection of Remote Key Relearn required to begin.
Doors lock-cycle (confirm)
5 ENGIN E START/STOP button used to confirm remote learning.

Programming with recognized remote keys — step sequence

Programming step
1 Scroll to DIC menu Remote Key Relearn and select to display READY FOR REMOTE #3, 4, 5, etc.
Programming step
2 Place new remote key into the rear cupholder when READY message appears.
Press / hold a fob button
3 Press ENGINE START/STOP to learn the remote; DIC confirms when learned.
Remove the key
4 Remove the remote key from the rear cupholder and press UNLOCK or LOCK on the remote after learning.
Programming step
5 Repeat placement and ENGINE START/STOP steps to program additional remotes.

Programming without recognized remote keys — procedure

Programming step
1 Locate an automotive locksmith in the area via provided phone number or website.
Programming step
2 Consider driving the vehicle to the locksmith if the vehicle is still mobile to save money.
Programming step
3 Locksmith uses specialized computer equipment to program the smart key remote fob.
Programming step
4 Two recognized remote keys are not required when locksmith services are used.

2022 Cadillac CT5

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (20 steps)

Vehicle capacity and requirements

Programming step
1 Vehicle supports up to eight remote keys matched to it
Programming step
2 New key programming requires two recognized keys when available
Programming step
3 Programming mode accessed via DIC menu labeled "Remote Key Relearn"
Programming step
4 DIC displays READY FOR REMOTE #3, 4, 5, etc., during learn process
Wait / timing window
5 Exit programming mode by pressing and holding ENGINE START/STOP for ~12 seconds

Programming with recognized remote keys (step-by-step)

Programming step
1 Place two recognized remote keys on the passenger seat
Programming step
2 Scroll to DIC menu and select Remote Key Relearn
Programming step
3 Place new remote key into the rear cupholder
Press / hold a fob button
4 Press ENGINE START/STOP; DIC indicates when remote is learned
Press LOCK + UNLOCK
5 Remove new remote, press UNLOCK or LOCK; repeat for additional remotes

Programming flow and repetition

Programming step
1 DIC shows readiness to program the next remote after each successful learn
Programming step
2 Repeat Steps 4–5 to program additional remote keys as needed
Programming step
3 Continue until all additional remote keys are programmed
Wait / timing window
4 Finalize by holding ENGINE START/STOP for approximately 12 seconds to exit
Programming step
5 Sequence requires vehicle to be in RUN and both recognized and new remotes present

Programming without recognized remote keys

Programming step
1 Two recognized remote keys required; if unavailable, alternative needed
Programming step
2 Locate an automotive locksmith using provided phone number or website
Programming step
3 Driving vehicle to locksmith may be more cost-effective than onsite visit
Programming step
4 Locksmith uses specialized computer equipment to program smart key remote fob
Programming step
5 Procedure required when vehicle lacks two currently recognized remotes

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

YearRoute statusExact steps
2020Route verifiedGeneral guidance
2021Route verifiedGeneral guidance
2022Route verifiedGeneral guidance

Common questions

What type of key does a 2020-2022 Cadillac CT5 use?

It uses a smart proximity key fob for push-button start, with an internal emergency mechanical key blade for manual door unlocking.

Can I get an aftermarket key fob for my 2020-2022 Cadillac CT5?

Yes. Aftermarket smart key fobs compatible with 2020–2022 CT5 models are available and typically use FCC ID YG0G20TB1.

Does the CT5 key fob have a physical key inside?

Yes. The CT5 smart key contains a removable emergency mechanical key used for unlocking the door if the fob battery is dead.

Can you program a CT5 key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your CT5 fob programmed? We come to you, 24/7.
Scroll to Top
☎  Tap to call 24/7 — (833) 439-8636