Chevrolet Tracker Key Fob Programming by Year

Can you program a Tracker fob without the dealer? For most years, yes. Pick your year for the route and best next step.

Find your year

YearDIY onboard?How it programsWorking fob?Erase riskConfidenceBest next step
2000–2004YesYes - onboard relearnYesHighFollow the steps below

Chevrolet Tracker key types & programming facts

2000-2004 Chevrolet Tracker models in the U.S./Canada use a traditional mechanical ignition key and a separate keyless entry remote fob, rather than a transponder or proximity system. Replacement remotes can be added using an onboard programming procedure that uses the vehicle’s diagnostic link connector to place the body control/keyless system into learn mode, then teaches the vehicle each fob’s lock/unlock signal without a scan tool. Mechanical keys are cut to match the existing lock cylinders, with no immobilizer chip programming required.

Key types used on the Tracker:

  • non-transponder mechanical key with separate keyless entry remote (2000-2004)

Common fob FCC IDs: AB01502T, ABO1502T — check the back of your fob; we confirm the exact variant on site.

2000–2004 Chevrolet Tracker

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (18 steps)

Preparation

Programming step
1 Locate Data Link Port under dash on driver's side
Programming step
2 Identify pins numbered 8 and 4 on Data Link Port
Programming step
3 Verify presence of metal contact pins in terminals 8 and 4
Programming step
4 Obtain suitable jumper wire to connect terminals 8 and 4
Programming step
5 Keep jumper wire connected throughout programming procedure

Entering Programming Mode

Programming step
1 Connect terminal 8 to terminal 4 with jumper wire
Press LOCK + UNLOCK
2 Vehicle confirmation: doors lock and unlock to signify entering programming mode
Programming step
3 Ensure jumper remains connected during transmitter programming
Programming step
4 Know exact terminals 8 and 4 before applying jumper
Programming step
5 Programming mode initiated prior to pressing transmitter buttons

Transmitter Programming Steps

Press LOCK + UNLOCK
1 Press and hold both LOCK and UNLOCK buttons together on first transmitter
Press LOCK + UNLOCK
2 Hold buttons about 15 seconds until vehicle locks and unlocks to confirm programming
Programming step
3 Release buttons on the transmitter after vehicle response
Programming step
4 Within one minute, repeat same procedure for remaining transmitters to be programmed
Programming step
5 Program all desired transmitters during the same programming session

Completion and Troubleshooting

Programmer / scan tool
1 Remove jumper wire from OBDII Port to exit programming procedure
Programming step
2 Reminder to check key fob battery if key fob not working
Programming step
3 Link provided to find replacement key fob if needed

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

YearRoute statusExact steps
2000–2004Route verifiedGeneral guidance

Common questions

Does my 2000-2004 Chevy Tracker key have a transponder chip?

No. These Tracker models use a standard mechanical key with a separate keyless entry remote and do not use a transponder or push‑to‑start system.

Can I program a new remote for my Chevy Tracker myself?

Yes. 1999-2004 Tracker remotes can be programmed with an onboard procedure using the diagnostic link connector; no dealer scan tool is required.

Which remote works with a 2000-2004 Chevrolet Tracker?

Aftermarket and OEM suppliers list a 2‑button GM remote commonly marked with FCC ID ABO1502T/AB01502T as fitting 2000-2004 Chevrolet Tracker models.

Can you program a Tracker key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your Tracker fob programmed? We come to you, 24/7.
Scroll to Top
☎  Tap to call 24/7 — (833) 439-8636