Kia Sedona Key Fob Programming by Year

Can you program a Sedona fob without the dealer? For most years, yes. Pick your year for the route and best next step.

Find your year

YearDIY onboard?How it programsWorking fob?Erase riskConfidenceBest next step
2003–2005YesYes - onboard relearnNo (all-keys-lost OK)MedFollow the steps below

Kia Sedona key types & programming facts

2003–2005 Kia Sedona models in the U.S./Canada use a conventional metal ignition key and a separate 3‑button keyless entry remote. Programming of the remote can be performed via an onboard procedure using the vehicle’s diagnostic connector and ignition cycle, without special scan tools. Cutting of the mechanical key is handled separately by a locksmith or dealer using standard key‑cutting equipment.

Key types used on the Sedona:

  • non-transponder metal key with separate keyless entry remote (2003-2005)

Common fob FCC IDs: PLN BONTEC, PLNBONTEC-003 — check the back of your fob; we confirm the exact variant on site.

2003–2005 Kia Sedona

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (18 steps)

Vehicle and access limits

Programming step
1 Model year specified: 2003 Kia Sedona
Programming step
2 Keyless entry remote fob programming applicable
Doors lock-cycle (confirm)
3 Horn confirmation: horn will sound when locking
Programming step
4 Diagnostic connector location: near battery under hood

Diagnostic connector and jumper layout

Programming step
1 Jumper pin layout illustrated: row showing "1 23 4"
Programming step
2 Additional pins shown: "678910 11 1213 14 15 16"
Programming step
3 Lower pins shown: "181920"
Programming step
4 Required jump: pin 5 to pin 17 with suitable jumper wire
Programming step
5 Warning: use of suitable jumper wire implied for safety/connection

Ignition and programming sequence

Programming step
1 open hood and locate diagnostic connector near battery
Programming step
2 jump pin 5 to pin 17 with suitable jumper wire
Turn ignition to ON
3 turn ignition to the ON position (DO NOT START)
Press / hold a fob button
4 press LOCK button of first remote two times
Press / hold a fob button
5 press LOCK button on second remote two times (if applicable)

Final steps and verification

Remove the key
1 Turn ignition OFF and remove key after remote button presses
Programming step
2 Disconnect jumper from diagnostic connector following key removal
Press LOCK + UNLOCK
3 Check for lock and unlock operation to verify programming
Programming step
4 Horn will sound when locking as part of verification

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

YearRoute statusExact steps
2003–2005Route verifiedGeneral guidance

Common questions

Does my 2003-2005 Kia Sedona key have a transponder chip?

Available sources describe a standard metal key paired with a separate keyless entry remote, with no specific mention of a transponder chip for 2003–2005 Sedona models.

Can I program a replacement remote for my 2003-2005 Kia Sedona myself?

Yes. These Sedona years support onboard programming of the 3‑button keyless entry remote using an ignition cycle and the under‑hood diagnostic connector.

Which remote will fit my 2003-2005 Kia Sedona?

Locksmith suppliers list a 3‑button keyless entry remote for 2003–2005 Sedona with FCC ID PLN BONTEC or PLNBONTEC-003 as compatible.

Can you program a Sedona key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your Sedona fob programmed? We come to you, 24/7.
Scroll to Top
☎  Tap to call 24/7 — (833) 439-8636