For the Outlander, replacement key/fob options vary by trim and model year, with earlier vehicles using remote entry fobs and later vehicles using smart/proximity-style fobs. The source material indicates programming routes include onboard and OBD, but it does not provide a year-by-year factory programming matrix here, so the exact method depends on the specific year and system equipped.
Key types used on the Outlander:
2-button remote keyless entry remote (2003-2006)
3-button smart key fob remote (2008-2021)
4-button smart key fob remote (2014-2020)
5-button key fob remote starter (2011-2019)
5-button smart key fob remote (PHEV) (2018-2020)
Common fob FCC IDs: OUCG8D-525M-A, OUC644M-KEY-N, MZ360340EX — check the back of your fob; we confirm the exact variant on site.
2003–2006 Mitsubishi Outlander
Route verified — exact steps vary by trim/equipment
Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.
Show the programming methods (20 steps)
2) Preparation Steps
Programming step
1 Locate the Data Port under drivers side dashboard, usually to the right of steering column
Insert the key
2 Insert keys in ignition and leave in the OFF position
Programming step
3 Verify metal contact pins present in terminals 1 and 4
Programming step
4 Identify which terminals are numbered 1 and 4 before connecting jumper
Programming step
5 Obtain a suitable jumper wire and plan to leave it connected throughout programming
3) Entering Programming Mode
Programming step
1 Connect Data Port terminals 1 and 4 with suitable jumper wire
Programming step
2 Perform connection within the sequence prior to pressing vehicle switches
Press / hold a fob button
3 Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times
Press LOCK + UNLOCK
4 Confirmation of programming mode: doors will automatically lock and unlock once
Programming step
5 Keep jumper wire connected for entire programming procedure
4) Programming Remotes
Press / hold a fob button
1 Press the LOCK button on the remote to be registered three times within 10 seconds
Press LOCK + UNLOCK
2 Successful programming indicated when doors lock and unlock once
Programming step
3 Repeat registration step for additional remotes (up to 4 total) within one minute
Press LOCK + UNLOCK
4 After each successful programming the doors will lock and unlock once
Programming step
5 Include any existing remotes when counting total remotes to register
5) Completion and Troubleshooting Notes
Programming step
1 Disconnect the programming wire after completing programming
Remove the key
2 Remove the keys from the ignition to finish the procedure
Programming step
3 Reminder to try replacing the key fob battery if key fob not working
Programming step
4 Links provided for battery replacement and key fob replacement (Click Here)
Programming step
5 Printed instruction available (Print Instruction)
This year needs a programmer/scan tool - there is no owner-followable onboard sequence. A mobile locksmith confirms your key type and FCC ID, then programs it on site.
Route verified — exact steps vary by trim/equipment
Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.
Show the programming methods (29 steps)
Vehicle types and prerequisites
Programming step
1 Regular key or remote head key requires two already programmed working keys to add a key (except Canada)
Programming step
2 Smart Key system requires two already programmed Smart Keys and one properly cut emergency key to add a Smart Key (except Canada)
Programming step
3 If fewer than required programmed keys are available, locksmith needed to program an additional key
1 Insert first programmed key into ignition, turn to ON for 5 seconds
Turn ignition to ON
2 Turn first key to LOCK position and remove
Insert the key
3 Within 30 seconds, insert second programmed key, turn to ON; immobilizer light blinks ~10 seconds later
Insert the key
4 When immobilizer light blinks, turn second key to LOCK, remove, then within 30 seconds insert new unprogrammed key and turn to ON
Cycle the ignition ON/OFF
5 Successful programming indicated by immobilizer light ON for 3 seconds then OFF; repeat steps 1–4 to program additional keys
Programming remote-head key (remote portion)
Programming step
1 Requirement: one already programmed remote to enter programming mode
Press LOCK + UNLOCK
2 Enter programming: press UNLOCK 4–10 seconds on programmed remote, then press and hold LOCK
Press LOCK + UNLOCK
3 Within 10 seconds, release LOCK and UNLOCK in sequence; all remotes except the used one are erased and doors lock/unlock to confirm programming mode
Cycle the ignition ON/OFF
4 Program each remote within 60 seconds: press both LOCK and UNLOCK simultaneously 2 seconds, release 1 second, press UNLOCK and release; locks will cycle if successful
Wait / timing window
5 Exit programming if no remotes added within 60 seconds; test all remotes after completion
Smart Key programming (fob-to-start portion)
Remove the key
1 Remove emergency key from back of Smart Key and remove ignition switch cover while pushing lock release buttons
Insert the key
2 Insert emergency key into ignition, then insert first programmed Smart Key into emergency key and turn to ON for 5 seconds
Insert the key
3 Turn first Smart Key to LOCK; within 30 seconds insert second programmed Smart Key and turn to ON; immobilizer light blinks ~10 seconds later
Insert the key
4 When immobilizer light blinks, turn second Smart Key to LOCK and remove; within 30 seconds insert new unprogrammed Smart Key and turn to ON
Cycle the ignition ON/OFF
5 Successful programming indicated by immobilizer light ON for 3 seconds then OFF; repeat process from step 1 to program additional Smart Keys
Smart Key programming (remote/button portion)
Insert the key
1 Begin by removing emergency key and ignition cover, insert emergency key, insert first programmed Smart Key and turn to ON; perform subsequent steps within 30 seconds
Remove the key
2 Remove first Smart Key; press UNLOCK and LOCK simultaneously on first programmed Smart Key for 4–10 seconds, then release LOCK and UNLOCK in sequence within 10 seconds
Press LOCK + UNLOCK
3 With second programmed Smart Key, press UNLOCK 4–10 seconds and press LOCK during this time; release LOCK and UNLOCK in sequence within 10 seconds; immobilizer light blinks on multi-information display
Press / hold a fob button
4 Within 60 seconds, press LOCK twice with new unprogrammed Smart Key; immobilizer light on information screen comes on for 30 seconds
Programming step
5 Programming completion indicated by display behavior described in prior steps; repeat as needed for additional Smart Keys
Indicators, errors, and testing
Programming step
1 Immobilizer light blinking signals initiation of key programming windows
Wait / timing window
2 For key programming success, immobilizer light comes on for 3 seconds then goes off
Wait / timing window
3 For Smart Key button programming, immobilizer light appears on multi-information display and new key causes 30-second display light when LOCK pressed twice
Programming step
4 If an error occurs, immobilizer light will go off during procedure
Programming step
5 Final step for any method: test all remotes/keys after programming completion
Route verified — exact steps vary by trim/equipment
Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.
Show the programming methods (20 steps)
Vehicle types and prerequisites
Programming step
1 Regular key or remote head key procedures applicable (except for cars sold in Canada)
Programming step
2 Smart Key system procedures applicable (except for cars sold in Canada)
Programming step
3 Requirement: two already programmed working keys or Smart Keys to add a new one
Programming step
4 If fewer than two programmed keys, locksmith required to program additional key
1 Insert first programmed key, turn to ON for 5 seconds
Remove the key
2 Turn first key to LOCK, remove first key
Insert the key
3 Within 30 seconds insert second programmed key, turn to ON; immobilizer light begins blinking ~10 seconds later
Insert the key
4 When immobilizer blinks, turn second key to LOCK, remove; within 30 seconds insert new unprogrammed key, turn to ON; immobilizer light on 3 seconds indicates success
Programming step
5 Repeat steps 1–4 to program additional keys; immobilizer light off during procedure indicates error
Remote head key remote programming
Programming step
1 Requirement: at least one already programmed remote to enter programming mode
Press LOCK + UNLOCK
2 Enter programming mode: use programmed remote, press UNLOCK 4–10 seconds, then press and hold LOCK
Press LOCK + UNLOCK
3 Release LOCK and UNLOCK in sequence within 10 seconds to erase other remotes; doors lock/unlock confirming programming mode
Press LOCK + UNLOCK
4 Program remotes (within 60 seconds): press LOCK+UNLOCK together 2 seconds, release 1 second, press UNLOCK and release; locks will confirm success
Wait / timing window
5 Exiting: no additional remotes within 60 seconds exits programming mode; test all remotes after programming
Smart Key programming steps
Close the doors
1 Preparation: open driver door and keep open until programming finished; do not open/close other doors
Insert the key
2 Step with first programmed Smart Key: carry key, turn ignition to ON without starting (perform within 30 seconds), insert new Smart Key into slot
Press LOCK + UNLOCK
3 With first programmed Smart Key press UNLOCK 4–10 seconds and press LOCK during this time; release LOCK and UNLOCK in sequence within 10 seconds
Press LOCK + UNLOCK
4 Repeat similar sequence with second programmed Smart Key (press UNLOCK 4–10 seconds, press LOCK, release in sequence); immobilizer will blink on multi-information display
Wait / timing window
5 Completion: buzzer sounds 3 times and immobilizer display on 30 seconds indicates success; buzzer 3 seconds indicates termination on error; repeat from step 1 to program additional Smart Keys
Keys & fobs that fit the 2014–2018, 2020 Outlander
Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.
Year
Route status
Exact steps
2003–2006
Route verified
General guidance
2007–2009
Route verified (tool)
Professional route
2010–2013
Route verified
General guidance
2014–2018, 2020
Route verified
General guidance
Common questions
Does every Mitsubishi Outlander use the same key fob?
No. The Outlander uses different remote and smart key fob types across model years and trims, including 2-button, 3-button, 4-button, and 5-button variants.
Can a replacement Outlander fob be programmed?
Yes, but the programming route depends on the specific year and system. Available source material indicates onboard and OBD programming are used across this model range.
Are there FCC IDs listed for Outlander remotes?
Yes. The source lists OUCG8D-525M-A, OUC644M-KEY-N, and MZ360340EX for certain Outlander remote/fob listings.
Can you program a Outlander key fob without going to the dealership?
For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.
Does this program the remote only, or the transponder key too?
It depends on your key type. Tell us your FCC ID and we will confirm.
What if my year says professional programming required?
Those years need a programmer or security access; we bring the tool to you and program it on site.
How much does it cost?
It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.
Need your Outlander fob programmed? We come to you, 24/7.
