What year ranges does this guide cover?

This guide covers the source-backed year clusters: 2007, 2008u20132011, and 2012u20132013.

Does this program the remote only, or does it also program an immobilizer transponder?

The procedures described are for keyless-entry remote pairing and confirmation signals (locks cycling and, where equipped, buzzer confirmation). Transponder and immobilizer enrollment is not covered by these source-backed steps.

What should be checked first if the remote does not work?

The source-supported first troubleshooting step is to replace the battery and re-test the remote before repeating the procedure.

When should DIY attempts stop and professional help be used?

Professional help is appropriate when confirmation signals do not occur after repeating the supported steps, or when the source indicates special equipment is required for a smart key system.

Can a replacement remote be added without affecting existing remotes?

Not always. The source warns that some programming sessions erase previously stored remote codes, so all remotes should be present when programming.

Suzuki SX4 Key Fob Programming by Year

Can you program a SX4 fob without the dealer? For most years, yes. Pick your year for the route and best next step.

☎ Call (833) 439-8636

Find your year

Year	DIY onboard?	How it programs	Working fob?	Erase risk	Confidence	Best next step
2007	Yes	Yes - onboard relearn	No (all-keys-lost OK)	None known	Med	Follow the steps below
2008–2011	Yes	Yes - onboard relearn	No (all-keys-lost OK)	Possible	Med	Follow the steps below
2012–2013	Yes	Yes - onboard relearn	—	Yes	Med	Follow the steps below

Suzuki SX4 key types & programming facts

For the Suzuki SX4, the key system uses a separate remote keyless entry fob paired with a conventional mechanical ignition key, with the remote operating door lock/unlock and related convenience functions. Programming replacement remotes for this model can be done by following an onboard pairing procedure using the vehicle’s ignition and existing key, without specialized diagnostic equipment in many cases. A compatible remote must match the original FCC ID (such as KBRTS003 or replacement KBRTS005) for reliable operation.

Key types used on the SX4:

remote keyless entry remote (separate from mechanical key) (2007-2013 (remote functions; mechanical key type not specified in sources))

Common fob FCC IDs: KBRTS003, KBRTS005 — check the back of your fob; we confirm the exact variant on site.

2007 Suzuki SX4

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (19 steps)

Preparation Steps

Remove the key

1 Remove key from ignition switch.

Close the doors

2 Close all doors.

Programming step

3 Open drivers door.

Programming step

4 Have key and remote(s) available before starting procedure.

Programming step

5 Note timing requirements specified in subsequent steps.

Programming Sequence

Remove the key

1 Insert key and turn to ON position; within 10 seconds turn key off and remove key.

Close the doors

2 Within 20 seconds close and open drivers door 3 times.

Remove the key

3 Insert key and turn to ON position; within 10 seconds turn key off and remove key.

Press LOCK + UNLOCK

4 Confirmation of programming mode occurs when locks automatically lock and unlock.

Cycle the ignition ON/OFF

5 Press the UNLOCK button on remote to program; locks should cycle to confirm.

Multiple Remotes and Exit Procedure

Press / hold a fob button

1 Repeat UNLOCK press step for each additional remote.

Programming step

2 Exit vehicle with keys and remote after programming.

Close the doors

3 Close door and test remote(s) to verify operation.

Programming step

4 Replace battery suggested if key fob not working.

Formatting and Printing

Programming step

1 Option available: Print Instruction.

Programming step

2 Step-by-step instructions provided in numbered format.

Programming step

3 Headings and step labels included for clarity.

Programming step

4 Contact information and website navigation included for further assistance.

Programming step

5 Copyright and site name displayed at document end.

Keys & fobs that fit the 2007 SX4

Suzuki 2-Button Remote Head KeyRemote KeyView fob →Suzuki OEM Smart Key FobSmart KeyView fob →Suzuki 2-Button Remote Head KeyRemote KeyView fob →

For the 2007 SX4: SX4 key replacement & all compatible fobs →

2008–2011 Suzuki SX4

Route verified — exact steps vary by trim/equipment

Show the programming methods (25 steps)

Vehicle Types and Notes

Programming step

1 Separate key and remote system instructions apply to vehicles with distinct key and remote units.

Programming step

2 Smart Key System instructions apply to vehicles equipped with integrated keyless start and entry.

Programming step

3 Up to four remote controller codes can be stored in vehicle memory.

Programming step

4 Programming a new remote erases all previously stored remote codes automatically.

Programming step

5 Attempting to program a fifth code clears all four stored codes automatically.

Preparation Steps Before Programming

Remove the key

1 Remove key from ignition switch and ensure all doors are closed for separate-key method.

Doors lock-cycle (confirm)

2 Confirm drivers door is unlocked and all doors closed for Smart Key method.

Programming step

3 Have all remote controllers available before beginning Smart Key programming.

Insert the key

4 Sit in the driver’s seat and insert key into ignition switch when instructed.

Wait / timing window

5 Complete specified step sequences within provided time limits (25 seconds or 60 seconds as noted).

Separate Key and Remote Programming Sequence

Close the doors

1 Remove key from ignition, close all doors, open driver’s door before beginning.

Remove the key

2 Insert key, turn to ON, within 10 seconds turn OFF and remove key.

Close the doors

3 Within 20 seconds, close and open driver’s door three times.

Remove the key

4 Insert key, turn to ON, within 10 seconds turn OFF and remove key; locks should cycle confirming programming mode.

Press / hold a fob button

5 Press UNLOCK on remote to program; repeat for each additional remote and test by exiting and closing door.

Smart Key Programming Sequence (Timed Steps)

Remove the key

1 After inserting key, complete steps A–E within 25 seconds: lock then unlock door switch, repeat twice, lock, remove and reinsert key, repeat sequence three more times.

Turn ignition to ON

2 Start engine: turn ignition to START and wait 3 seconds after final repetition.

Wait / timing window

3 Proceed to step 5 within 60 seconds after engine start to continue programming.

Cycle the ignition ON/OFF

4 Turn ignition to LOCK; buzzer sounds twice and door lock switch cycles automatically.

Cycle the ignition ON/OFF

5 Press LOCK, UNLOCK, or PANIC on remote within 30 seconds; buzzer sounds twice and lock switch cycles to confirm program; repeat for additional remotes.

Verification, Security, and Troubleshooting

Remove the key

1 After programming completion, remove key from ignition or turn ignition to ON to finish procedure.

Programming step

2 Verify keyless start and keyless entry systems operate properly using each remote controller.

Programming step

3 If unable to operate systems, repeat entire programming procedure.

Programming step

4 To change remote codes after a loss, program new remote(s) to erase old codes; all remotes must be programmed together.

Programming step

5 Replace key fob battery if remote not working; replacement and fob info referenced (links indicated).

Keys & fobs that fit the 2008–2011 SX4

Suzuki 2-Button Remote Head KeyRemote KeyView fob →Suzuki OEM Smart Key FobSmart KeyView fob →Suzuki 2-Button Remote Head KeyRemote KeyView fob →

For the 2008–2011 SX4: SX4 key replacement & all compatible fobs →

2012–2013 Suzuki SX4

Route verified — exact steps vary by trim/equipment

Show the programming methods (23 steps)

Programming methods

Programming step

1 Separate key and remote system procedure provided

Programming step

2 Smart Key System requires special equipment; no onboard programming

Programming step

3 Battery replacement recommended as troubleshooting step

Programming step

4 Links referenced for battery and key replacement (Click Here)

Separate key and remote programming steps

Remove the key

1 Remove key from ignition switch

Close the doors

2 Close all doors, then open driver’s door

Remove the key

3 Insert key, turn to ON, within 10 seconds turn key off and remove key

Close the doors

4 Within 20 seconds close and open driver’s door three times

Remove the key

5 Insert key, turn to ON, within 10 seconds turn key off and remove key; locks should lock/unlock to confirm programming mode

Remote pairing actions

Cycle the ignition ON/OFF

1 Press UNLOCK button on remote to confirm programming; locks should cycle

Press / hold a fob button

2 Repeat UNLOCK press for each additional remote

Programming step

3 Exit vehicle with keys and remote after programming

Close the doors

4 Close door and test remote(s)

Doors lock-cycle (confirm)

5 Locks cycling used as confirmation at multiple stages

Troubleshooting and requirements

Programming step

1 Smart Key System requires special equipment connected to vehicle for programming

Programming step

2 No onboard programming procedure for Smart Key System

Programming step

3 Battery replacement suggested if key fob not working

Programming step

4 Replacement key fob and battery links provided

Programming step

5 Local locksmith assistance available via provided phone number

Page and legal information

Programming step

1 Title: Suzuki SX4 Keyless Entry Remote Fob Smart Key Programming Instructions

Programming step

2 Print instruction option mentioned

Programming step

3 Home, Disclaimer, YouTube, Privacy Policy links listed

Programming step

4 Instructional content distinguishes between two system types (separate key vs Smart Key)

Keys & fobs that fit the 2012–2013 SX4

Aftermarket Smart Key FobSmart KeyView fob →Suzuki 2-Button Remote Head KeyRemote KeyView fob →Suzuki OEM Smart Key FobSmart KeyView fob →Suzuki 2-Button Remote Head KeyRemote KeyView fob →

For the 2012–2013 SX4: SX4 key replacement & all compatible fobs →

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

Year	Route status	Exact steps
2007	Route verified	General guidance
2008–2011	Route verified	General guidance
2012–2013	Route verified	General guidance

Common questions

Does my 2007-2013 Suzuki SX4 use a separate remote and key?

Yes. Available sources show a standalone remote keyless entry fob paired with a standard mechanical ignition key for the SX4 in this period.

Which FCC IDs are commonly listed for Suzuki SX4 remotes?

Documented remotes for the SX4 include FCC ID KBRTS003, with KBRTS005 listed as a replacement remote sharing the same compatibility range.

Can Suzuki SX4 remotes be programmed without special dealer tools?

Yes. For SX4 remotes with FCC IDs such as KBRTS003, suppliers provide onboard pairing instructions using the vehicle’s ignition sequence and existing key.

Can you program a SX4 key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your SX4 fob programmed? We come to you, 24/7.

Call (833) 439-8636 Get a quote