Honda OEM Transponder Key (chip ID13) – Fitments, Specs & Programming
Programming a Honda OEM Transponder Key (chip ID13) requires a compatible automotive key programmer capable of reading and writing Megamos crypto transponders. The procedure begins with inserting the blank into the ignition cylinder and initiating the vehicle’s immobilizer learning sequence, which varies slightly across the covered model years. Locksmiths cloning this key must first verify the existing immobilizer system recognizes the ID13 chip family before attempting enrollment. A Honda OEM Transponder Key (chip ID13) enrolled correctly will allow the engine control module to authenticate the transponder signal and permit ignition. Replacement units of this transponder typically ship as uncut blanks with the HON58R keyway profile, requiring precision cutting to the vehicle’s original bitting code before programming can proceed. The device covers a broad range of Honda and Acura platforms manufactured between 1991 and 2006, making it one of the more versatile OEM transponder blanks in the Honda ecosystem.
Honda OEM Transponder Key (chip ID13) – Technical Specifications
The ID13 transponder integrated into this key is manufactured by Megamos, a well-established supplier of automotive immobilizer chips used across several OEM platforms. The Megamos ID13 is a fixed-code transponder — it does not use rolling cryptographic authentication like later-generation chips. This characteristic simplifies cloning procedures but also means the immobilizer system relies on a static handshake between the transponder and the vehicle’s engine control unit. The chip sits embedded in the bow of the key and is energized inductively by the antenna ring surrounding the ignition lock cylinder.
The mechanical blade uses the HON58R keyway profile, a standard Honda high-security cut that fits the corresponding lock cylinders across the validated fitment list. HON58R blanks feature a single-sided milling pattern. Locksmiths should confirm the key bitting through either code retrieval from the vehicle’s lock or by decoding an existing working key, since even small deviations in cut depth can cause binding in the ignition wafer stack.
Megamos ID13 Chip – Background and Programming Notes
Megamos Crypto transponders have been in automotive use since the early 1990s, and the ID13 variant was adopted by Honda for its first wave of factory immobilizer-equipped vehicles. Unlike the later ID46 and ID48 chips — also Megamos products — the ID13 operates on a simpler authentication protocol. This makes it compatible with a wide range of aftermarket key programmers, including popular units from Autel, Xtool, and the Silca RW4 platform.
When programming the transponder to a vehicle, the procedure generally follows one of two paths. If at least one working key exists, many programmers can clone the ID13 chip directly, producing a duplicate that the immobilizer accepts without any on-board programming steps. In scenarios where no working key is available, the locksmith must interface with the vehicle’s immobilizer ECU — typically through the OBD-II port or by direct EEPROM access — to register the new transponder’s fixed code into the system’s memory. The specific method depends on the year, model, and ECU generation installed in the vehicle.
Validated Vehicle Fitments
The following Honda and Acura models have been validated for use with this transponder key and the HON58R blade profile. Year ranges indicate the production spans during which the ID13 immobilizer system was factory-installed.
Acura Models
- Acura CL — 1997–1999 and 2000–2003 model years
- Acura Integra — 1994–2001
- Acura MDX — 2001–2006
- Acura NSX — 1991–2005
- Acura RL — 1996–2004
- Acura RSX — 2002–2004
- Acura TL — 1999–2003
Honda Models
- Honda Accord — 1997–2002
- Honda Civic — 2000–2005
- Honda Insight — 1999–2006
- Honda Odyssey — 1999–2004
- Honda Prelude — 1996–2001
- Honda S2000 — 1999–2003
It is worth noting that some late-production vehicles in the above ranges may have transitioned to a newer immobilizer generation. Locksmiths should always verify the transponder type by reading the existing key or querying the immobilizer module before cutting and programming a replacement. Attempting to register an ID13 chip into a system expecting a later-generation transponder will result in a failed enrollment.
Blade Cutting and Mechanical Considerations
The HON58R keyway requires a code-cutting machine equipped with the appropriate Honda clamp and cutter. Common code machines from Silca (Futura series), Keyline (Ninja series), and HPC all support this profile. The blade’s single-sided track means only one milling pass is necessary, but depth accuracy must be held to tight tolerances — Honda wafer locks are known for narrow depth increments, and an imprecise cut can cause intermittent mechanical failure even if the transponder programs successfully.
When the original key is available for duplication, a tracer-guided cut on a standard duplicating machine is sufficient. For code-origination jobs where no sample key exists, the locksmith must either decode the lock cylinder directly or pull the key code from Honda’s code database using the VIN. Honda key codes from this era are generally accessible through standard locksmith code retrieval services.
When to Contact a Locksmith
Vehicle owners driving any of the Acura or Honda models listed above should be aware that the transponder key cannot simply be duplicated at a hardware store kiosk. While the mechanical blade can be cut on basic equipment, the Megamos ID13 chip requires programming to the vehicle’s immobilizer before the engine will start. A qualified automotive locksmith with the appropriate diagnostic tool can handle both the cutting and programming on-site, typically completing the job in under thirty minutes per key.
Dealership key replacement for these older Honda and Acura models tends to carry a significant markup compared to independent locksmith pricing. Since the ID13 transponder is well-supported by aftermarket programming tools, independent locksmiths can generally offer this service at a lower cost with equivalent results. The key itself, when sourced as a genuine Honda OEM blank, provides the same fit, finish, and durability as the original factory key.
Specifications and fitment
| Key type | Transponder Key |
|---|---|
| Transponder chip | ID13 |
| Chip manufacturer | Megamos |
| Keyway | HON58R |
| FCC ID(s) | HON58R |
| Region(s) | USA |
| Product type | Transponder |
| Compatible makes | Acura, Honda |
Listed vehicle fitment
| Make | Model | Years |
|---|---|---|
| Acura | CL | 1997–1999 |
| Acura | CL | 2000–2003 |
| Acura | Integra | 1994–2001 |
| Acura | MDX | 2001–2006 |
| Acura | NSX | 1991–2005 |
| Acura | RL | 1996–2004 |
| Acura | RSX | 2002–2004 |
| Acura | TL | 1999–2003 |
| Honda | Accord | 1997–2002 |
| Honda | Civic | 2000–2005 |
| Honda | Insight | 1999–2006 |
| Honda | Odyssey | 1999–2004 |
| Honda | Prelude | 1996–2001 |
| Honda | S2000 | 1999–2003 |
Fitment must be confirmed against the existing key’s FCC ID family and the vehicle’s exact configuration before cutting or programming. VIN or photo verification may be required.
Questions and answers
Which vehicles does Honda OEM Transponder Key (chip ID13) fit?
Honda OEM Transponder Key (chip ID13) is listed to fit Acura, Honda applications such as Acura CL, Acura CL, Acura Integra, Acura MDX. Confirm the exact year range and the existing key’s FCC ID family before ordering, since fitment can vary by trim and region.
Does Honda OEM Transponder Key (chip ID13) need programming?
Yes. Because it carries a transponder/remote function (chip ID13), it must be programmed (paired) to the vehicle’s immobilizer and, for remote functions, to the keyless-entry system. Many vehicles also require at least one working key to add a new one.
Does the blade need to be cut?
Most Honda OEM Transponder Key (chip ID13) units ship uncut and require automotive key cutting before they will turn the ignition or door lock. Cutting establishes the mechanical match; programming establishes the electronic match — both are needed.
Is Honda OEM Transponder Key (chip ID13) OEM or aftermarket?
This listing is an aftermarket-grade replacement intended to match the original key’s electronic and mechanical specification. It is not required to carry a vehicle-brand logo and should be matched by FCC ID family and chip type rather than by appearance.
Check Fitment and Key Help
Low Rate Locksmith, a mobile automotive locksmith, can confirm whether Honda OEM Transponder Key (chip ID13) matches an existing FCC ID family and coordinate cutting and programming when the vehicle configuration requires professional service. For dispatch and support, call (833) 439-8636 or email info@lowratelocksmith.com.
Frequently asked questions
Get help for your vehicle
Share your year + situation and we'll confirm compatibility and a typical price range. Or call the dispatch number directly.
- ✅ Compatibility first
- 🧾 Itemized scope
- 🪪 Authorization required