Honda Accord Fob Replacement Service
Low Rate Locksmith Can help you with all of your Honda Accordkeys needs
We are mobile and we are available 24/7
We have techs available across the United States
Call us Now
24 Hour Service
Fast Response Time
1997 Accord fob programming instructions
1998 Accord fob programming instructions
1999 Accord fob programming instructions
2000 Accord fob programming instructions
2001 Accord fob programming instructions
2002 Accord fob programming instructions
2003 Accord fob programming instructions
2004 Accord fob programming instructions
2005 Accord fob programming instructions
2006 Accord fob programming instructions
2007 Accord fob programming instructions
Step-By-Step instructions to program 1997-2007 Honda Accord key fob (Method 1):
Note:
Entering the programming mode cancels all learned keyless remotes, so none
of the previously programmed remotes will work. You must reprogram all of the
keyless remotes once you are in the programming mode.
You must complete each step within 5 seconds of the previous step to keep the
system from exiting the programming mode.
1. Turn ignition switch to ON (II)
2. Press the LOCK or UNLOCK button on one of the remotes. (An unprogrammed
remote can be used for this step.)
3. Turn ignition switch to LOCK (0)
4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used
in step 2
5. Turn the ignition switch to ON (II)
6. Press the LOCK or UNLOCK button the same remote. Make sure the power door
locks cycle to confirm you are in programming mode.
7. Press the LOCK or UNLOCK button on each remote you want to program. Make
sure door locks cycle after you push each remote button to confirm system has
accepted the remote.
8. Turn the ignition switch to LOCK (0) to exit programming mode.
9. Test remote(s)
Step-By-Step instructions to program 1997-2007 Honda Accord key fob (Method 2):
Programming Notes:
Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
- ENTER the vehicle and CLOSE all doors. (Each of the following steps must be completed within five seconds of one another. If you take longer than five seconds between steps or make a mistake, you must start the entire procedure over.)
- INSERT the key into the Ignition, HOLD one remote in your left hand with additional remotes close by.
- PERFORM each of the next three (3) steps in order, then repeat all three (3) steps two (2) more times for a total of three (3) times each.
- TURN the Ignition to the ON position, marked “II” on the Ignition.
- PRESS the LOCK button on the remote for approximately 1 second. (Say “Mississippi”)
- TURN the Ignition to the OFF position, marked “I” on the Ignition. (REPEAT Steps 4-6 three (3) times)
- TURN the Ignition switch to the ON position, marked “II” on the Ignition.
- PRESS the LOCK button on the same remote. The door locks should cycle indicating the vehicle has ENTERED Programming Mode.
- PRESS the LOCK button again on the same remote. The door locks should cycle again indicating the vehicle has successfully PROGRAMMED that remote.
- For programming additional remotes to your vehicle, REPEAT Step 9 with each additional remote one after another. Step 9 must be completed within ten (10) seconds for each additional remote. You may program up to three (3) remotes to your vehicle.
- TURN the ignition to OFF.
- Test all remotes. Programming is now complete.
- After successful programming, if your remote has a TRUNK RELEASE Button — you will need to hold that button down for 5-10 seconds for that function to begin operation.
- If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
If you are looking for lost Accord car key replacement, click here to learn more
2008 Accord fob programming instructions
2009 Accord fob programming instructions
2010 Accord fob programming instructions
2011 Accord fob programming instructions
Step-By-Step instructions to program 2008-2011 Honda Accord key fob:
There is no on board programming procedure for Honda Accord 2008-2012. These vehicles requires special equipment be connected to the vehicle to program the keyless remote. Please contact your dealer or Honda automotive locksmith.
A maximum of 6 key remote transmitters can be programmed.
Program remote or key when remote transmitter added, replaced or system malfunction.
Immobilizer Programming and Operation
- System arms after switching ignition OFF
- Switch ignition ON
- Immobilizer warning lamp illuminates for a few seconds
- If immobilizer warning lamp illuminates for a few seconds then flashes rapidly. The key code is not recognized. Remove key and try again
- Immobilizer can only be programmed using diagnostic equipment