Here at Low Rate Automotive Locksmith we are your source for free instructions on how to program your Ford keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Locksmith offers detailed step-by-step directions from the manufacturer of your Ford key replacement car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.

 

 

1994-1998 Ford F250-550 Super Duty Car Key Fob and Remote Programming Instructions:

1. Turn ignition to RUN or ACC.

2. Momentarily jump pins in programming connector located at the base of the steering
column. All doors will lock then unlock to confirm programming mode.

3. Press any button on first keyless remote. Door locks will cycle to confirm programming.

4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.

5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

1999-2004 Ford F250-550 Super Duty Car Key Fob and Remote Programming Instructions:

1. Turn ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending
in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

If you have any questions or need a professional Locksmith To assist you with your Ford F250-550 Super Duty Key Fab Programming, below is a list of Low Rate Locksmith Locations.

2005-2010 Ford F250-550 Super Duty Car Key Fob and Remote Programming Instructions:

Procedure A:

1.Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.

2.Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1)

(Off is the position where you can remove your key, RUN is the position just shy of starting your car.)

3.Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
4.Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
5.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

*If this does not work try the procedure with the door closed.

Procedure B:
1. Fasten seatbelt and close all doors
2. Turn the ignition from OFF to RUN 4 times within 3 seconds.
3. Turn the ignition OFF. The system will chime to confirm programming mode.
4. Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
5. Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
6. Turn ignition to RUN to exit programming mode.

Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.

2010-2016 Ford F250-550 Super Duty Remote Fob Programming Instructions:

1. Close all doors then open drivers door press unlock button on drivers door while door is open . Insert key into ignition. Keep foot off brake pedal.

2. Turn ignition from Off to Run 8 times ending in Run ( Do not start the car, run position is just before the vehicle will start Off is turned all the way back when the key can be removed from the ignition ).  Must be performed within 10 seconds. Locks will cycle signaling entering into programming mode.

3. Press any button on the remote being programmed, locks cycle confirming programming. Repeat this step for any addition remotes.

4. Turn key to off, locks will cycle to end programming mode.

The Ford Super Duty is a line of trucks (over 8,500 lb (3,900 kg) GVWR) introduced in 1998 for the 1999 model year.  The Ford Super Duty trucks are larger, heavier built series pickup trucks with heavier-duty body-on-frame steel ladder frames, axles, springs, brakes, transmissions, more powerful engines, and all other heavier/bigger components (with much higher payload and towing capacities) than the older traditional equivalent Ford F-250.